Description

Double-packed epoxy-vinyl enamel.

Recommended use 

Protective and decorative painting of  metal,  concrete and reinforced concrete structures  used in atmospheric conditions  of all macroclimate  areas, atmosphere types and placement categories according to GOST 15150. Oil-,  gasoline-proof  coating  is  resistant to  spills of  oil and petroleum products,  sea  and fresh water, short-term exposure  to  hot water and steam,  aggressive environments,  sudden temperature changes (from minus 60 to plus 60 °C).
Used as  a  finishing  coat  in complex coating systems with  VINICOR-061 (TU  20.30.12-001-54359536-2018),  VINICOR-marine  (TU 20.30.12-004-67503963-2018),  VINICOR-ecoprime  (TU  2312-002-67503963-2011),  ZINEP  (TU 20.30.12-022-12288779-2018),  ZINOTAN  (TU  2312-017-12288779-2003), ZINOL  (TU 2313-012-12288779-99)  primers,  with  VINICOR-ecoprime  (TU  20.30.12-010-67503963-2017) primer-enamel, with VINICOR-63 (TU 2313-007-67503963-2013) varnish, as well as with other primers on vinyl-epoxy and epoxy bases.

Certificates, Approvals

State registration certificate No. RU.78.01.06.008.Е.000564.12.18 dated 11.12.2018
Oil and gas industry: included into the JSC “Transneft” Register
Transport construction:  standards STO-0139367-007-2015 and STO-01393674-008-2014 of  АО Central Research Institute of Transport Construction, STO 12288779-001-2018 of  State Company "Avtodor".
Approved by test centers: All-Union Research Institute for Construction and Operation of Pipelines, Melnikov Central Research and Design Institute of Steel Structures, Research Institute of Coating Industry with Experimental Mechanical Plant “Viktoriya”, AOOT All-Union Research Institute Neftekhim, Railway Research Institute,  АО  Central  Research Institute of Transport Construction, Federal State Unitary Enterprise “A.P.Alexandrov Research Technological Institute”.
It has a certificate of voluntary certification system of the Russian River Register No. POCC RU.PO00.H00269.

Surface preparation

The surface prepared for applying varnish coat should be  cleaned from dirt, degreased, if necessary, dust and moisture shall be removed.

Application 

• mix base thoroughly to homogenous condition before application;
• With constant stirring, add a hardener to the base and mix thoroughly;

The mixing ratio of the base and hardener EN-02, EN-03 (by mass) 100:2.9 respectively;

• if necessary, the composition should be diluted to the working viscosity;
• hold the prepared material before applying for 15-20 minutes with a covered lid.

The material is recommended to be applied  in the plant  and field  conditions, dark colors at temperature  from  minus  10  to  plus  35  °C  and light colors at temperature from minus 5 to plus  35 °C at relative air humidity not more than 85 %.
The temperature of the painted surface shall be above the dew point by at least 3 °C. Prepared enamel shall be of temperature at least 15 °C.
The enamel  is recommended to be applied in 1-2 layers using airless,  conventional  (air) spray  by brush/roller.
The overlapping interval  between the layers of enamel at a temperature  (20±2)°C  –  not less than  3  hours.  Hardening  time depends on the temperature of the surface and ambient air, degree of dilution of the material, thickness of the coating, efficiency of ventilation and relative air humidity.
Holding  time  of the coating  before operating in aggressive conditions is not less than 7 days at temperature from 15 to 22 °С.

Storage and handling

The material  is delivered in packages: base and hardener packed in metal buckets and metal cans respectively depending on the set weight.
Storage conditions of  the  enamel components  –  according to GOST 9980.5 (at air temperature from minus 40 to plus 40 °C). The container shall be protected from atmospheric condensation and direct sunlight.
The  shelf life  is determined by warranty storage of the base (24 months) and hardener (12 months) starting with the manufacture date.

Precautions

When working with the  material,  one shall observe the existing sectoral standard norms and requirements and safety measures as specified on the package label.
One shall use personal protective equipment (goggles, face masks and respirators) and avoid inhalation of thinners and contact of the composition or its components with skin, eye mucosa, respiratory channels; use inside the premises is allowed only in case sufficient ventilation is provided.
The material and its components (base and hardener) are fire-hazardous!
The hardened coating is not harmful to human health.

The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the  VMP Holding CJSC  in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.