ISOLEP-SP-03

TU 20.30.12-021-67503963-2019

INTEROPERATIVE EPOXY PRIMER

Double-packed

Color: Red-brown, gray

Detailed characteristics      Find out the price

Recommended use

The epoxy primer ISOLEP-SP-03 is used for anti-corrosive protection of steel metal products as an interoperative primer during painting at the factory and/or temporary anti-corrosive protection during construction, as well as for additional protection of galvanized metal surfaces, aluminum products and its alloys.

 

Specifications

It can be overlapped with materials based on epoxy, vinyl-epoxy, vinyl-polyester, alkyd, urethane and acrylate bases

The coating can be thermally cutting and welded without increasing the porosity of the weld.

Coloring of AMg alloys and non-ferrous metals is allowed.

AREAS OF APPLICATION

ISOLEP-SP-03 primer is used for anti-corrosive protection of steel metal products as an interoperative primer for painting at the factory and/or temporary anti-corrosive protection during construction.

 

CERTIFICATION

Certificate of state registration No. RU.77.01.34.008.E.003242.12.21 dated 20.12.2021

 

Certificate of type approval: RUSSIAN MARITIME SHIPPING REGISTER No. 22.44.01.03918.120 (protective primer that allows welding to be performed without removing).

TECHNICAL SPECIFICATIONS

 Density         1.1 ± 0.1 g/cm3

 Proportion of non-volatile substances

 by volume, % (vol.)

 -by mass, % (mass.)

 

 25 ± 2 %

 42 ± 2 %

 Dry film thickness, microns          15-25*

 Drying time to degree 3

 at a temperature of (23 ± 2) ° C according to GOST 19007  10 min, no more

  Pot life at a temperature of (20 ± 2) ° C, h

 h, not less than       12, not less than

*Dry film thickness, 30-40 microns

CONSUMPTION PER M2

The theoretical consumption for a single-layer coating is 66-110 g/m2.

 

SURFACE PREPARATION

degrease metal surface to the first degree according to GOST 9.402;

clean the surface by abrasive blasting from scale, rust to degree 2 according to GOST 9.402 (Sa 2½ according to ISO 8501-1). In hard-to-reach places and when painting small areas, cleaning with a mechanical tool to a degree not lower than 3 according to ISO 8501-1 is permissible;

remove dust.

INSTRUCTIONS FOR USE

prior to use, mix the base thoroughly until smooth;

While mixing constantly add a curing agent to the base (the ratio is given in the quality certificate and on the container label) and mix thoroughly.

The material is recommended to be applied in the factory at a temperature of plus 5 to plus 35 ° C with a relative humidity of no more than 85%.

Temperature of the painted surface must be at least 3 °C above the dew point.

The curing time depends on the surface temperature and ambient air, coating thickness, ventilation efficiency and relative humidity.

 

Recommended application parameters:

Automatic line

 

Recommended diluent

Without dilution

Nozzle diameter

0.011’-0.017’ (0.28-0.43 mm)

Pressure

10 - 15 MPa (100 - 150 bar)

Airless spraying

Recommended diluent       Without dilution

Nozzle diameter       0.011’-0.017’ (0.28-0.43 mm)

Pressure       10 - 15 MPa (100 - 150 bar)

Pneumatic application

Recommended diluent       Without dilution

Nozzle diameter       1.8 - 2.2 mm

Pressure       0.2-0.4 MPa (2-4 bar)

Brush / Roller

Recommended diluent       Without dilution

Equipment cleaning

SOLVIN-15 (TU 20.30.22-014-67503963-2018)

 

STORAGE OF ANTI-CORROSIVE PRIMER

The material is supplied complete set: the base is packed in a metal bucket with a capacity of 20 liters, hardener is in a metal bucket with a capacity of 10 liters.

 

Storage conditions is in accordance with GOST 9980.5 (at ambient temperatures from minus 40 to plus 40 °С). When storing containers with material components, they should not be placed near heat sources, exposed to atmospheric precipitation, or direct sunlight.

 

The shelf life is 12 months from the date of manufacture with the right to prolong further storage

 

SECURITY MEASURES

When working, observe the relevant industry standards and requirements, as well as the precautions indicated on the packaging label.

 

Use personal protective equipment (glasses, masks, respirators), avoid inhalation of solvents during evaporation and contact of the material or its components with the skin, mucous membranes of the eyes and respiratory tract; use indoors only if sufficient ventilation is provided.

 

The material and its components (base and hardener) are flammable!

 

Information provided is general in nature and does not take into account the specifics of a particular object.